Owatrol Oil

Rs. 1,669.00

A high-quality rust inhibitor & oil based paint conditioner

  • Penetrates deep, drives out moisture & air from rusted metal.
  • Stabilizes the rust and prevents it from reforming.
  • Additive for oil based paints & wood stains.
  • Improves flow of paint and eliminates brush & roller marks.
  • Prevents cracking & peeling with improved paint adhesion.
  • Increase coverage of coat up to 25%.
Size:  

Owatrol Oil is versatile, highly penetrating air drying oil that can be used alone or added to paint. Used alone as a rust inhibitor it provides a tough, flexible finish, driving out excess moisture and air; displacing it from rusted metal, so stopping rust dead in its tracks. Used alone on porous wood surfaces it will saturate and protect the wood from damage caused by moisture and prevent paint from peeling.

When added as a paint conditioner to any oil or alkyd based coatings it will give increased wet edge time, improved flow and greater adhesion. Unlike damaging thinners, it will maintain the inherent quality of the paint without affecting its appearance or drying times, allowing you to achieve a more professional finish.

Using Owatrol Oil as a rust inhibitor

Owatrol Oil penetrates through the rusted metal to the sound metal below, isolating it and protecting it from further rusting. Directly use on rusted surfaced – the penetrating oil drives out moisture and air and stabilises the metal to protect it from future damage.

On brand new metal surfaces, use Owatrol’s AP 60 instead. If you are looking for a high gloss rusted finish you can also overcoat the surface with Deks Olje D2 high gloss clear oil.

Using Owatrol Oil to aid adhesion

A bonding film is left on all surfaces Owatrol Oil is used on which maintains the natural look of the surface but allows enhanced adhesion, making it perfect as a foundation for primers or finishing coats. It gives excellent adhesion including on galvanised steel, aluminium, zinc, wood and more. Paint can be applied directly to firm rust when Owatrol Oil is used and is heat resistant up to +175°C.

Using Owatrol Oil as a paint conditioner

Mix Owatrol Oil into oil-based paints as a paint conditioner to get several great benefits. Firstly, it gives the paint rust-inhibiting properties and helps prevent rust on painted surfaces (even when rust is already present). Secondly, it also improves the flow and workability of the paint. This means that you can maintain the ‘wet edge’ for longer, reducing brush and roller marks. Finally, it gives the paint a better viscosity allowing painting work to be carried out in a more extreme cold, hot and windy conditions. Unlike damaging paint thinners, it does all this without altering the inherent qualities or the finish of the paint.

Please note that if you are looking for a product to give this effect but for water-based paints then please use Floetrol instead as it is designed for use in any water-based paint whereas Owatrol Oil is for use in oil-based paints.

Using Owatrol Oil for wood impregnation

When used on wood surfaces Owatrol Oil saturates the wood and protects it from damage caused by moisture. It also helps to prevent paint from peeling and protects metal parts such as hinges and latches from corrosion.

Ideal Uses for Owatrol Oil

  • Priming galvanised surfaces with no need for weathering or pickling
  • Preventing further damage in heavily rusted surfaces
  • Improving paint flow when working in cold environments
  • Preventing peeling paint on wood surfaces
  • Protecting metal part on wood surfaces like gates and window frames
  • Assuring better adhesion of finishes

 

Application tools

  • Brush
  • Roller
  • Airless or HVLP sprayer
  • Pump sprayer

Surface Preparation

Surface preparation when using Owatrol Oil as a rust inhibitor

First, surfaces must be clean, dry and free from oil, grease and other surface contaminants. Remove all scale; loose and flaking rust and old paint back to a sound surface and edge and feather in any sharp edges. Surfaces exposed to chemicals (acids, alkalis or salt deposits) should be washed using copious amounts of water or steam cleaned. Severely contaminated surfaces should be cleaned using an appropriate solvent.

Do not remove firm rust or clean the metal back to a bright finish.

Surface preparation when using Owatrol Oil as a paint conditioner

First, prepare the surface as per the instructions on your paint can. In addition, if not asked to, ensure that you remove all loose and flaking material and treat any organic growth with a fungicidal solution or a mix of 1 part water to 1 part chlorine bleach (allow the bleach solution to sit for 15 minutes), rinse thoroughly and allow to dry.

Applying Owatrol Oil as a Rust Inhibitor

Using Owatrol Oil on new clean steel

First prime new steel with a mix of 1 part Owatrol Oil to 3 parts primer. Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.

Using Owatrol Oil on lightly rusted surfaces

First prime the surface with a mix of 1 part Owatrol Oil to 2 parts primer. Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.

Using Owatrol Oil on new unpainted rusty steel

First prime the surface with a mix of 1 part Owatrol Oil to 1 part primer. Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.

Using Owatrol Oil on old, severely rusted or previously coated surfaces

First, apply wet-on-wet applications of Owatrol Oil to all exposed rust until fully saturated and allow it to dry. Saturation is indicated by a uniform glossy appearance to the surface when Owatrol Oil is dry.

Before Owatrol Oil has hardened, check the surfaces and remove rust scale and old paint loosened by the above. If needed, touch up these areas. Allow to dry. Next, apply a mix of 1 part Owatrol Oil to 2 parts primer and allow to dry.

Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.

Note: Owatrol Oil will not lift well-bonded paint.

Applying Owatrol Oil as a Paint Conditioner

Apply the paint in a normal manner. If the paint is sticky, drags, sets up too fast or does not level properly, add more Owatrol Oil (stirring in well) until the paint works smoothly, easily and evenly. Allow the brush, roller or sprayer to be your guide.

Using Owatrol Oil as a Paint Conditioner for wood surfaces in sound condition

First prime any bare wood with a mix of 1 part Owatrol Oil to 2 parts primer and allow to dry. Follow with normal paint system adding Owatrol Oil as in ‘Mixing Instructions’ below.

Using Owatrol Oil as a Paint Conditioner on damaged, soft or punky wood surfaces

First apply 2 to 4 liberal applications of Owatrol Oil wet-on-wet, as fast as the wood will absorb it. Do not allow Owatrol Oil to dry between applications. When the wood cannot absorb any more, wipe up any excess and allow to dry overnight (12 hrs). Follow with normal paint system adding Owatrol Oil as in ‘Mixing Instructions’ below to ease application and aid adhesion.

Mixing instructions

Topcoat: As required – normally 5 %-20 % by volume.
Undercoat: up to 30 % by volume.
Primer: up to 50 % by volume.

The above is meant as a guide only. Conditions of application, the porosity of surface etc. will dictate the amount of Owatrol Oil to be mixed into the paint.

Clean Up

Clean all tools and equipment with white spirits while still wet. If allowed to dry, remove with paint stripper. Store and maintain equipment as directed by the manufacturer.

NOTE: Any rags, steel wool etc soaked in Owatrol Oil may spontaneously catch fire if improperly discarded. Rags, steel wool etc must be saturated with water after use or placed in a sealed, water-filled metal container, before disposing of with household waste.

Restrictions

Do not mix or overcoat Owatrol Oil with paints containing hot solvents i.e. Xylene, 2 part coatings, chlorinated rubber etc. – for these type of paints use Owatrol CIP instead. Do not use Owatrol Oil as a paint conditioner in water-based paints, for this purpose use Easy Flow instead – Owatrol’s water-based paint conditioner.

Things to Remember

  • Cover everything you do not wish to paint.
  • Apply between + 5°C and + 35°C.
  • Do not apply in direct sunlight or on to hot surfaces.
  • Test for compatibility when adding Owatrol Oil to paint.

15

Coverage Calculator

Technical Data

Coverage: 18m2 (194 ft²) per litre
Tools: Brush, Roller, Airless or HVLP Sprayer, Garden sprayer, pump sprayer
Suitable for: Exterior & Interior use
Clean up: White Spirit
Drying Time: Touch Dry: 12 hours, Full Dry: 24 hours depending on temperature and humidity
Re-coating Time: 24-48 hours
Finish: Transparent Matt

Related Products